Sandtex Trade – Eggshell X-tra is a high performance, solvent based eggshell finish, which has been specially formulated to provide long lasting protection for exterior joinery and suitably primed metal.

It is possible to add a light colour to the white Eggshell X-tra.

Drying Time:

In good conditions, touch dry after six hours and recoatable after sixteen – twenty-four hours.
Previous coat must be fully dry before another application.

Coverage:

12-15m² per litre depending on the surface texture.

Weather conditions:

Don’t apply when air or substrate temperatures are likely to fall below 8ºC, or when the relative humidity is above 80% during application or the drying period.

Preparation:
All new metals:

Lightly abrade to a bright (not polished) surface – excluding galvanised surfaces.
Wash with hot water and Sugar Soap to remove oil, grease or any other contaminants, rinse thoroughly with clean waterand  allow surface to dry, then prime.

New Wood Surfaces :

Surfaces must be sound, clean, suitably dry and free from anything that will interfere with the adhesion of the materials to be applied.
Rub down with a suitable grade of sand paper and remove all dust.
Timber with oils or extractives must be swabbed with clean methylated spirits, frequently changing the face of the cloth.
Treat knots with two coats of  knotting and fill any fixing holes, open joints and shallow surface defects with a filler.
Apply the primer undercoat.

Previously Decorated Wood:

All surfaces must be sound, clean, suitably dry and free from anything that will interfere with the adhesion of the materials to be applied.
Remove all loose, failing or suspect paint, also remove grey and denatured surfaces by rubbing down with abrasive paper and feather edges of sound paint.
Remove all dust, and any defective putty glazing.
Clean and prime rebates, aiso replacement putties must be allowed to form a hard skin before being painted.
Treat knots with two thin coats of knotting and fill any fixing holes, cracks and shallow surface defects with a filler.
Wash remaining sound paint with hot water and a liquid detergent solution to remove any contaminants.
Wet abrade to provide a key, rinse with clean water to remove all residues and allow to dry.

APPLICATION:
Stir well before and during use.
Apply using good quality tools – a synthetic or bristle brush or a short/medium pile roller and maintain a wet edge.

CLEANING:
Return surplus material to container.
Wash tools and equipment with White Spirit immediately after use.

STORAGE:
Store upright and secure.
Store in secure dry conditions inaccessible to children or animals.
Containers should be kept closed during storage.
Don’t store below 5ºC or above 40ºC.

We are available via WhatsApp – click here:

The post Sandtex Trade – Eggshell X-tra – White – 2.5L appeared first on Midi Décor St Chinian.

A high-performance exterior gloss system which provides greater resistance to cracking and flaking than traditional Gloss.

It is possible to add a light colour to the Flexigloss X-tra.

There’s a number of ways you can choose a paint colour:
From the RAL Classic range by clicking on the colour grid.
Or contact us if you a have a specific colour in mind and we can tell you whether we can make it for you.

We are available via WhatsApp – click here:
And email: mididecorstchinian@gmail.com

Drying Time:

In good conditions, touch dry after six hours and recoatable after sixteen – twenty-four hours.
Previous coat must be fully dry before another application.

Coverage:

12-15m² per litre depending on the surface texture.

Weather conditions:

Don’t apply when air or substrate temperatures are likely to fall below 8ºC or when the relative humidity is above 80% during application or the drying period.

Preparation:
All new metals:

Lightly abrade to a bright (not polished) surface – excluding galvanised surfaces.
Wash with hot water and Sugar Soap to remove oil, grease or any other contaminants, then rinse thoroughly with clean water, allow the surface to dry, and prime with Sandtex Trade Flexible Primer Undercoat.

New Wood Surfaces :

Surfaces must be sound, clean, suitably dry and free from anything that will interfere with the adhesion of the materials to be applied.
Rub down with a suitable grade of abrasive paper and round sharp edges to a 1-3mm radius, remove all dust.
Timber with oils or extractives must be swabbed with clean methylated spirits, frequently changing the face of the cloth.
Treat knots with two coats of  knotting and fill any fixing holes, open joints and shallow surface defects with a filler.
Apply the primer undercoat.

Previously Decorated Wood:

All surfaces must be sound, clean, suitably dry and free from anything that will interfere with the adhesion of the materials to be applied.
Remove all loose, failing or suspect paint, also remove grey and denatured surfaces by rubbing down with abrasive paper and feather edges of sound paint.
Remove all dust, and any defective putty glazing.
Clean and prime rebates, aiso replacement putties must be allowed to form a hard skin before being painted.
Treat knots with two thin coats of knotting and fill any fixing holes, cracks and shallow surface defects with a filler.
Wash remaining sound paint with hot water and a liquid detergent solution to remove any contaminants.
Wet abrade to provide a key, rinse with clean water to remove all residues and allow to dry.

APPLICATION:
Stir well before and during use.
Apply using good quality tools – a synthetic or bristle brush or a short/medium pile roller and maintain a wet edge.

CLEANING:
Return surplus material to container.
Wash tools and equipment with White Spirit immediately after use.

STORAGE:
Store upright and secure.
Store in secure dry conditions inaccessible to children or animals.
Containers should be kept closed during storage.
Don’t store below 5ºC or above 40ºC.

We are available via WhatsApp – click here:

The post Sandtex Trade – FlexiGloss X-tra – Colour – 2.5L appeared first on Midi Décor St Chinian.

You can choose a paint colour from the RAL Classic range by clicking on the colour grid provided or contact us if you a have a specific colour in mind and we can tell you whether we can make it for you.

We are available via WhatsApp – click here:
And email: mididecorstchinian@gmail.com

Crown Trade Matt Vinyl has excellent opacity, with good colour retention.
Also, a low sheen finish which is quick drying and is a true flat matt

Limitations:

Matt Vinyl is for interior use only.

Do not apply when air or substrate temperatures are likely to fall below 8ºC or when the relative humidity is above 80% during application or the drying period.

The paint is touch dry in 1 hour and recoatable after 4 hours.

Preparation:

Surfaces must be sound, clean, suitably dry and free from anything that will interfere with the adhesion of the materials to be applied – e.g. dirt, grease etc.
Porous surfaces should be coated with a ‘mist’ coat of Crown Trade Matt Vinyl diluted with 40% clean water by volume.
Remove all loose, failing or suspect paint.
Fill any fixing holes, cracks and shallow surface defects with a filler.
Any glossy or eggshell surfaces should be wet abraded to provide a key.
Rinse with clean water to remove all residues.
Allow to dry.

Coating System:

Apply two coats as required.
Certain colours may require additional coats to give complete obliteration.

Application:
Stir well before use.
Apply by brush or medium roller.
For airless spray (dilution may be
required).
For further information contact the Crown Trade Customer Relations Team.

Cleaning:
Return surplus material to container.
Wash your brush or roller with clean water immediately after use.

The post Crown Trade – Matt Vinyl – Colour – 1L appeared first on Midi Décor St Chinian.

A premium quality silk emulsion for interior use on wall and ceiling surfaces, where a washable high sheen finish is required.

Ways to choose a paint colour:
The RAL Classic range by clicking on the colour grid provided.
Contact us if you a have a specific colour in mind and we can tell you whether we can make it for you.

We are available via WhatsApp – click here:
And email: mididecorstchinian@gmail.com

PREPARATION:

New Surfaces:
Surfaces must be sound, clean, suitably dry and free from anything that will interfere with the adhesion of the materials to be applied.
Porous surfaces should be coated with a ‘mist’ coat of Crown Trade Silk Vinyl diluted with 40% of clean water.

Previously Decorated Surfaces:
Surfaces must be sound, clean, suitably dry and free from anything that will interfere with the adhesion of the materials to be applied.
Remove loose, failing or suspect paint.
Fill holes, cracks and shallow surface defects with a filler.
Wash paint with hot water and sugar soap to remove any contaminants.
Glossy or eggshell surfaces should be wet abraded to provide a key.
Rinse with clean water.
Allow to dry.

COATING SYSTEM:

Apply two coats as required.
Certain colours may require additional coats to give complete obliteration.
Do not apply when air or substrate temperatures are likely to fall below 8ºC.
Relative humidity must be below 80% during application and the drying period.

APPLICATION:

Stir well before use.
Apply with a brush Cervus or a medium pile roller.
For airless spray (dilution may be required).

CLEANING:

Return surplus material to the container.
Wash brushes and rollers with clean water immediately after use.

The post Crown Trade – Silk Vinyl – Colour – 2.5L appeared first on Midi Décor St Chinian.

FastFlow Quick Dry Satin Finish has an excellent opacity, and a fabulous smooth, attractive finish.

The paint has all the characteristics of a traditional solvent based satin, with the added benefits of a water based formulation, including quick drying and low odour.

There’s a number of ways you can choose a paint colour:
From the RAL Classic range by clicking on the colour grid provided.
Or contact us if you a have a specific colour in mind and we can tell you whether we can make it for you.

We are available via WhatsApp – click here:
And email: mididecorstchinian@gmail.com

Drying Time:

In good conditions, Fastflow is touch dry after 1-2 hours and recoatable in 4-6 hours but always ensure that the previous coat is fully dry though before applying a second coat.
During low temperatures or high humidity, drying times may be extended.
Fastflow finishes to a satin sheen.

Coverage:

Can cover up to 15m² per litre depending on the surface texture.

Limitations:

Don’t apply when the air or substrate temperatures are likely to fall below 8°C, or when the relative humidity is above 80% during application or the drying period, as this could affect the adhesion of the paint to the surface.

How to prepare new surface timber and timber based boards (Including MDF):

Treat knots with two coats of knotting, then fill any fixing holes, open joints and shallow surface defects with a Ready Mixed Filler.
Rub down with a suitable grade of abrasive sandpaper and remove all dust after sanding.
All surfaces must be suitably dry, and free from anything that will interfere with the adhesion of the paint.
Prime with one coat of Crown Trade Fastflow Quick Dry Primer Undercoat.

All metals:

Surfaces must be clean and free from anything that will interfere with the materials to be applied.
Lightly abrade to a bright (not polished) surface – excluding galvanised surfaces, then wash with hot water and Sugar Soap solution to remove oil, grease or any other contaminants, frequently changing the water.
Rinse thoroughly with clean water and allow to dry.

Fastflow coverage:

For best results apply two coats.
Be aware that newly painted doors and windows should not be closed until the paint is fully dry.

How to Apply Fastflow Quick Dry Satin Finish:

Stir well before use.
Apply using a good quality synthetic brush or a good quality micro fibre medium pile roller to achieve an even layer.
To assist application on porous substrates the surface may be dampened slightly, and maintain a wet edge.
On timber, lay off in the direction of the grain and avoid excessive de-nibbing in-between coats.
If using an airless spray, dilution may be required.

Cleaning your brushes/rollers:

Clean all equipment with clean water immediately after use.

Also available in 2.5L FastFlow Quick Dry Satin

The post Crown Trade – FastFlow Quick Dry Satin Finish – Colour – 1L appeared first on Midi Décor St Chinian.

There’s a number of ways you can choose a paint colour:
From the RAL Classic range by clicking on the colour grid provided.
Or contact us if you a have a specific colour in mind and we can tell you whether we can make it for you.

We are available via WhatsApp – click here:
And email: mididecorstchinian@gmail.com

Crown Trade Matt Vinyl has excellent opacity, with good colour retention.
Also, a low sheen finish which is quick drying and is a true flat matt

Limitations:

Matt Vinyl is for interior use only.

Do not apply when air or substrate temperatures are likely to fall below 8ºC or when the relative humidity is above 80% during application or the drying period.

The paint is touch dry in 1 hour and recoatable after 4 hours.

Preparation:

Surfaces must be sound, clean, suitably dry and free from anything that will interfere with the adhesion of the materials to be applied – e.g. dirt, grease etc.
Porous surfaces should be coated with a ‘mist’ coat of Crown Trade Matt Vinyl diluted with 40% clean water by volume.
Remove all loose, failing or suspect paint.
Fill any fixing holes, cracks and shallow surface defects with a filler.
Any glossy or eggshell surfaces should be wet abraded to provide a key.
Rinse with clean water to remove all residues.
Allow to dry.

Coating System:

Apply two coats as required.
Certain colours may require additional coats to give complete obliteration.

Application:
Stir well before use.
Apply by brush or medium roller.
For airless spray (dilution may be
required).
For further information contact the Crown Trade Customer Relations Team.

Cleaning:
Return surplus material to container.
Wash your brush or roller with clean water immediately after use.

The post Crown Trade – Matt Vinyl – Colour – 250ml appeared first on Midi Décor St Chinian.

There’s a number of ways you can choose a paint colour:
From the RAL Classic range by clicking on the colour grid provided.
Or contact us if you a have a specific colour in mind and we can tell you whether we can make it for you.

We are available via WhatsApp – click here:
And email: mididecorstchinian@gmail.com

Crown Trade Matt Vinyl has excellent opacity, with good colour retention.
Also, a low sheen finish which is quick drying and is a true flat matt

Limitations:

Matt Vinyl is for interior use only.

Do not apply when air or substrate temperatures are likely to fall below 8ºC or when the relative humidity is above 80% during application or the drying period.

The paint is touch dry in 1 hour and recoatable after 4 hours.

Preparation:

Surfaces must be sound, clean, suitably dry and free from anything that will interfere with the adhesion of the materials to be applied – e.g. dirt, grease etc.
Porous surfaces should be coated with a ‘mist’ coat of Crown Trade Matt Vinyl diluted with 40% clean water by volume.
Remove all loose, failing or suspect paint.
Fill any fixing holes, cracks and shallow surface defects with a filler.
Any glossy or eggshell surfaces should be wet abraded to provide a key.
Rinse with clean water to remove all residues.
Allow to dry.

Coating System:

Apply two coats as required.
Certain colours may require additional coats to give complete obliteration.

Application:
Stir well before use.
Apply by brush or medium roller.
For airless spray (dilution may be
required).
For further information contact the Crown Trade Customer Relations Team.

Cleaning:
Return surplus material to container.
Wash your brush or roller with clean water immediately after use.

The post Crown Trade – Matt Vinyl – Colour – 2.5L appeared first on Midi Décor St Chinian.

There’s a number of ways you can choose a paint colour:
From the RAL Classic range by clicking on the colour grid.
Or contact us if you a have a specific colour in mind and we can tell you whether we can make it for you.

We are available via WhatsApp – click here:
And email: mididecorstchinian@gmail.com

Sandtex Trade – Eggshell X-tra is a high performance, solvent based eggshell finish, which has been specially formulated to provide long lasting protection for interior and exterior joinery and suitably primed metal.

Ideally your project will need a suitable, solvent based primer undercoat and Sandtex Trade Flexible Primer Undercoat is the perfect partner.

Drying Time:

In good conditions, touch dry after six hours and recoatable after sixteen – twenty-four hours.
Previous coat must be fully dry before another application.

Coverage:

12-15m² per litre depending on the surface texture.

Weather conditions:

Don’t apply when air or substrate temperatures are likely to fall below 8ºC.
Avoid painting when the relative humidity is above 80% during application or drying period.

Preparation:
All new metals:

Lightly abrade to a bright (not polished) surface – excluding galvanised surfaces.
Wash with hot water and Sugar Soap to remove oil, grease or any other contaminants.
Rinse thoroughly with clean water, allow the surface to dry, then prime.

New Wood Surfaces :

Surfaces must be sound, clean, suitably dry and free from anything that will interfere with the adhesion of the materials to be applied.
Rub down with a suitable grade of abrasive paper and round sharp edges to a 1-3mm radius, remove all dust.
Timber with oils or extractives must be swabbed with clean methylated spirits, frequently changing the face of the cloth.
Treat knots with two coats of  knotting and fill any fixing holes, open joints and shallow surface defects with a filler.
Apply the primer undercoat.

Previously Decorated Wood:

Surfaces must be sound, clean, suitably dry and free from anything that will interfere with the adhesion of the materials to be applied.
Remove all loose, failing or suspect paint, also remove grey and denatured surfaces by rubbing down with abrasive paper and feather edges of sound paint.
Remove all dust, and any defective putty glazing.
Clean and prime rebates, aiso replacement putties must be allowed to form a hard skin before being painted.
Treat knots with two thin coats of knotting and fill any fixing holes, cracks and shallow surface defects with a filler.
Wash remaining sound paint with hot water and a liquid detergent solution to remove any contaminants.
Wet abrade to provide a key, rinse with clean water to remove all residues and allow to dry.

APPLICATION:
Stir well before and during use.
Apply using good quality tools – a synthetic or bristle brush or a short/medium pile roller and maintain a wet edge.

CLEANING:
Return surplus material to container.
Wash tools and equipment with White Spirit immediately after use.

STORAGE:
Store upright and secure.
Store in secure dry conditions inaccessible to children or animals.
Containers should be kept closed during storage.
Don’t store below 5ºC or above 40ºC.

The post Sandtex Trade – Eggshell X-tra – Colour – 2.5L appeared first on Midi Décor St Chinian.

There’s a number of ways you can choose a paint colour:
From the RAL Classic range by clicking on colour grid.
Or contact us if you a have a specific colour in mind and we can tell you whether we can make it for you.

We are available via WhatsApp – click here:
And email: mididecorstchinian@gmail.com

Sandtex Trade – Eggshell X-tra is a high performance, solvent based eggshell finish, which has been specially formulated to provide long lasting protection for interior and exterior joinery and suitably primed metal.

Ideally your project will need a suitable, solvent based primer undercoat and Sandtex Trade Flexible Primer Undercoat is the perfect partner.

Drying Time:

In good conditions, touch dry after six hours and recoatable after sixteen – twenty-four hours.
Previous coat must be fully dry before another application.

Coverage:

12-15m² per litre depending on the surface texture.

Weather conditions:

Don’t apply when air or substrate temperatures are likely to fall below 8ºC.
Avoid painting when the relative humidity is above 80% during application or drying period.

Preparation:
All new metals:

Lightly abrade to a bright (not polished) surface – excluding galvanised surfaces.
Wash with hot water and Sugar Soap to remove oil, grease or any other contaminants.
Rinse thoroughly with clean water, allow the surface to dry, then prime.

New Wood Surfaces :

Surfaces must be sound, clean, suitably dry and free from anything that will interfere with the adhesion of the materials to be applied.
Rub down with a suitable grade of abrasive paper and round sharp edges to a 1-3mm radius, remove all dust.
Timber with oils or extractives must be swabbed with clean methylated spirits, frequently changing the face of the cloth.
Treat knots with two coats of  knotting and fill any fixing holes, open joints and shallow surface defects with a filler.
Apply the primer undercoat.

Previously Decorated Wood:

Surfaces must be sound, clean, suitably dry and free from anything that will interfere with the adhesion of the materials to be applied.
Remove all loose, failing or suspect paint, also remove grey and denatured surfaces by rubbing down with abrasive paper and feather edges of sound paint.
Remove all dust, and any defective putty glazing.
Clean and prime rebates, aiso replacement putties must be allowed to form a hard skin before being painted.
Treat knots with two thin coats of knotting and fill any fixing holes, cracks and shallow surface defects with a filler.
Wash remaining sound paint with hot water and a liquid detergent solution to remove any contaminants.
Wet abrade to provide a key, rinse with clean water to remove all residues and allow to dry.

APPLICATION:
Stir well before and during use.
Apply using good quality tools – a synthetic or bristle brush or a short/medium pile roller and maintain a wet edge.

CLEANING:
Return surplus material to container.
Wash tools and equipment with White Spirit immediately after use.

STORAGE:
Store upright and secure.
Store in secure dry conditions inaccessible to children or animals.
Containers should be kept closed during storage.
Don’t store below 5ºC or above 40ºC.

The post Sandtex Trade – Eggshell X-tra – Colour – 1L appeared first on Midi Décor St Chinian.

It is possible to add light colours to the Masonry paint.
This can be done by using the RAL Classic colour grid provided, or contact us via WhatsApp or email if you have a specific light colour in mind.
We are available via WhatsApp – click here:
And email: mididecorstchinian@gmail.com

Sandtex Microseal Smooth Masonry Paint is microporous and provides sealing attributes that protect the coating against water ingress.

This means that the coating allows the surface to breathe and moisture to evaporate whilst at the same time protecting the coated surface from water penetration.

The advanced coating protects over an extended period against mould and algae growth.

Its dirt resistant properties also help to maintain the coating’s aesthetic features, and with the benefit of being rainproof in just 1 hour you can complete the job even if the weather forecast is not reliable.

With 15 years trusted durability, you can ensure that your house looks better for longer.

• 15 years trusted durability
• Breathable
• Resists peeling and flaking
• Dirt resistant
• Mould and algae resistant
• Rainproof in just 1 hour
• Smooth paint finish
• Covers 12 -16 sq metres per litre

SUITABLE SURFACES:

Suitable: For use on most sound, dry exterior surfaces including render, roughcast, pebbledash, concrete, building blocks, facing bricks and previously painted surfaces.
Not Suitable: On common, fletton or engineering type bricks.

PREPARATION:

General Preparation: All surfaces must be sound, clean, dry and free from anything that will interfere with the adhesion of the paint.
New surfaces usually require little preparation but must be completely dried out before painting.
Loose or Flaking Material: Remove all loose and flaking material by scraping or brushing with a stiff bristle brush (not wire).
Chalking, Weathered. Powdery or Porous Surfaces: These surfaces should be brushed down and treated with an application of Stabilising Solution.
As with all coatings preparation is key and poor preparation will result in poor coating performance.

APPLICATION:

General Application:
Stir well before and during use.
Apply with a good quality masonry brush, exterior roller or airless spray.
See spray manufacturer’s instructions for guidelines on application.
Do not apply if there is a risk of rain or frost, or if the temperature will fall below 8°C during drying.

Drying Time: Re-coatable after 3-4 hours in normal conditions.

Cleaning: Wash all equipment in clean water immediately after use.

 STORAGE:

Ensure this pack is stored upright and secure at all times. Do not store below 5°C or above 40°C.
Crown Paints is not liable for decorating costs caused as a result of an incorrect colour being
applied, damage caused by spillage or a failure to follow manufacturer’s instructions.

The post Sandtex Retail – Microseal Smooth Masonry – 2.5L – White & light RAL Classic colours appeared first on Midi Décor St Chinian.